Site icon SewAndrew

How I Made My Jeans…

SewAndrew

I’m re-making my personalised jeans based on the Thread Theory Jutland Pants pattern… This time I’m personalising them a bit more. Also, rather than trying to get them done in a day, I’ve broken it down into 13 sections. This isn’t a sew along or a tutorial, it’s just a step by step of how I made them, with a few findings/ opinions along the way! If it helps, interests or encourages anyone, that’s a bonus! I’d love to hear your comments and tips too. It’s quite a long post, so I suggest making a cup of tea or pouring a glass of wine before you start reading!

So, if you’re sitting comfortably, I’ll begin…


I’ve already added a yoke, coin pocket and swapped the welt pockets out for patch (also button fly, but sticking with the zip for this pair).

This time I’ve lowered the rise a bit more, 2.5cm at the back and 3.5cm at the front. I’ve also tapered 6cm from each leg by marking 1.5cm in from the side seams at the hem of both front and back leg pieces, joining it up to the bottom of the pocket placement. Lastly I extended the left fly fold by 1cm to enable a wider top stitch on the front of the fly (this wasn’t necessary in the end, and just got in the way a bit!)

I got my denim from cheap fabrics online and I had some left over shirting for the pocket linings. Everything’s cut out and marked with my new crayons… ready to go…

Each of these sections make nice, bite sized, ‘after work’ pieces. But I wouldn’t recommend starting any of them too late. These are all the fiddly bits that show most at the end. I’m learning that by not doing too much in one go, I’m more exacting (& more likely to use the unpicker if somethings a bit wobbly!)


I don’t always follow the recommended order of construction, generally, I like to do all the little bits first. It’s a good idea to staystitch any curved or bias cuts and finish the edges of loosely woven fabrics, especially if they’re going to be taken out & put away a few times over the duration of your make. I’ve learned the hard way that this will help your pieces keep in shape. I’ve also learned the hard way not to finish the edges of pieces you intend to flat fell!

So, to warm up, I started with the belt loops. I used two threads in my needle to give me a strong (fake) topstitch; a tip I picked up from @Thriftystitcher‘s online tutorial, thank you!

1. Belt loops.

Then I stitched them using the stitch in the ditch foot, with my needle double threaded and ‘5 beeps’ to the left.

Then I put them away for later.

2. Front Pockets & Linings. 

I’ve added a coin pocket to the right front pocket. To make the pattern, I simply overlaid the paper pieces for the front, pocket lining & pocket facing. Then on another sheet of Swedish Tracing Paper I drew where I wanted the coin pocket, adding seam allowance on the two exposed sides.

I use the lock stitch function (on my Janome DKS30 – I LOVE my sewing machine!) to start & stop neatly. And I use the same settings for all my twin topstitching: 1st row, edgestitch with the ‘stitch in the ditch foot’ and needle offset 5 beeps left. 2nd row, topstitch with normal needle position & the edge of the foot against the previous row of stitching.


They’ll be back later, it’s back pockets next.

3. Back Pockets. 

I made a template of the finished pocket size. I use this for all the ironing so that both pockets are symmetrical.


Using the template on the right side (it’s my initials, so I’m not reversing the design) I mark the points of the design.

I poked through with a pencil first, tried one with chalk and the other with crayon.


It’s pretty clear to see that if I want to replace my chalk, I’m going to have to keep my crayons much sharper. The chalk was a much more precise line to follow, but I think the stitching both turned out the same… Washing will tell for sure.

To get the back pockets symmetrically placed, first I lay the back pieces down side by side, then lay the back pockets on the placement marks.

To double check I measure the distances from the edge at all the corners.

To triple check, once I’ve pinned them, I lay both trouser pieces right sides together, fold the top of the trouser piece back and check the pockets are laying on top of each other. Then…

Then, I’ll stitch them down. Still ‘double-threading’ and back to my ‘default-topstitch-spacing’ (D.T.S! -I’ve just made that up, I don’t really say that!)

Anyway, both back pockets are on. Before I put the backs away for a bit, it’s time to attach the yoke and finish the seat seam.

4. flat-felling the yoke.

If you’re doing this after work, you definitely want to wait until you’ve finished before opening the wine!

I do this exactly the same as Morgan’s method on the Thread Theory sew along.

Got it?!

I invested in a mini iron a while back. I don’t use it often, but it’s great for these fiddly bits (that, and asbestos fingers!). If that all went well it should end up looking something like this…

5. Sewing the Seat

Match up the seat seams and sew them, right sides together making sure the flat felling lines up. I do this by pinning the yokes together first on their stitching lines, then pin the rest of the seat seam… I’ve taken to stitching my seat seam three times!

  1. Once at the regular stitch length (2.4mm on my machine)
  2. Then again, same stitch length but shift the needle two beeps right.
  3. Then again back on the sewing line at 2 or 2.2mm stitch length.

(Perhaps this weakens the fabric…? I’ve decided it strengthens the seam!… Any suggestions?)

Then I give the edges a thorough zigzagging and clip into the curves. Here it is zigzagged…

When you’re looking at the insides, press the seam allowance over to the right and topstitch it down using the double thread trick again. You can stitch it twice to make it look like it’s been flat felled (I’m not keen on flat felling this seam because of the curve in it- it can be done… I’ve done it before… But I haven’t done it since!)

So here’s the back pieces joined together with pockets attached.

Baste the belt loops on and we’re done with the back pieces for now. 4cm from each side seam. 2.5cm either side of centre.


6. Attach the Front Pockets. 

It’s a nice touch to French seam the pocket bags.

This will make the pockets good and strong and give a nice clean finish to the insides. I was particularly fussy this time and even changed thread to match the pocket bags.


Once that’s done, line them all up and baste in place.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

* INTERMISSION *

 

Well, so far I’ve done five evening sessions. Each between 45min to an hour and a half. There’s not really too much to do, but with the fly, flat felling the inseam, the waistband and more still to go, were maybe just over the half way mark!

If you’re still reading this, I feel I should offer to make you a pair of jeans!

7. Fly

I’ve made probably 14 – 17 pairs of trousers in the two years I’ve been sewing (that shocked me when I added it up). Of course, I still find zip flies a bit daunting, but I follow Morgan’s instructions from the thread theory sewalong and apart from a couple of minor disasters, they’ve come out ok. I still don’t feel like I’ve ‘got it down’ though; even if I were to line up all the ones I considered a success, no two would look the same!

This time, I followed the Thread Theory instructions, only to hit a wobble on topstitching the curve. I even managed to wobble in the exact same spot on the 2nd row of stitching! This had to come out.

I waited a while until I had the patience to unpick it all and start again.

In the meantime, I came across This post from Closet Case Files on Twitter (actually, it was the Button Fly one I saw, they’re both the same technique, except for the button/zip bit). I thought it was time to try a new technique. (Please note, the failure of the first round was all to do with my sewing, and not the thread theory instructions! Although, I can get a pucker under my zip sometimes which doesn’t happen with the closet case method…)


I liked the idea of double topstitching the centre front too. It does take up quite a bit of space at the front though…. Maybe I should adjust my default topstitching measurements, but not now, it matches the pockets, I love it.


Almost there!


I ummed & ahhhd for ages about where to put the bar tacks. I even tried googling ‘fly front bar tacks’ to no(t much) avail. For no reason other than to put an end to the madness, I stuck them at 5 o clock and 10 past 3 on the fly curve. That’ll do.

8. Basting.

I figured I should try them on before it’s too late to change anything. Not a bad fit really. There seemed to be more fabric in the back than the front though. So I:


That looked better, certainly at the back leg. This made them a bit snug around my backside though. A bit too snug! So:

And guess what… They fit! So, it’s inseam, side seams, waistband & hems to go!

9. Flat-felling the Inseam. 

I do this slightly differently than the thread theory instructions. There seem to be lots of different methods (& tools!) for flat felled seams. This is how I’ve taken to doing it. This method results in a narrower seam, but, I think gives you more control. If you want to use this method & maintain a wider seam then you can increase the inside-leg seam allowance by 0.5cm. You only really need to do it to the front pieces, but I’d do it to both then there is no offsetting to confuse things.

First I had to unpick the basting as I need wrong sides together.

And there it is finished.

And from the inside, lovely.

Flat felling the inseam is a bit like going to the gym… I don’t believe anyone looks forward to it, but you get a great sense of achievement afterwards!

10. Out Seams

This is the easiest bit!


That’s it! I don’t recommend stitching this seam down, especially if you’ve tapered the legs. I only do it if I’m making denim shorts. I find it too difficult to sew up the tube, especially with a contrasting thread.

11. Waistband. 

I tried 2 different ways of attaching the waistband. I’m looking for the easiest order to complete all the visible topstitching I want. I’m not sure I e found it yet! So I’ve got green-version and orange-version. Personally, I think orange-version is better. You’ll see what happened to green-version in a minute…!

11a. Orange-Version.. (One piece waistband. More pics of green version, below!)

  1. Baste the belt loops into position.
  2. Sew the band, right sides together to the trousers.
  3. Press the seams up. (Leave the loops down for now)
  4. Press 1.3cm hem in inside of waistband.
  5. Create the ends by folding edge of band right sides together & sewing straight up in line with the front.
  6. Turn the band over and pin in the ditch from the right side. Catching the folded seam allowance at the inside.
  7. Stitch in the ditch using a matching thread. Leave the belt loops pointing down and out of the way.
  8. Still using matching thread, secure the belt loops below the waistband, to the trouser fronts. I use the width of the foot against the waistband seam to measure it.
  9. Change to topstitching thread and stitch around all sides of the waistband, close to the edge.
  10. Press the loops up, turn the ends over, stitch thoroughly in place, in line with the topstitching.
  11. Snip the ends of the loops off and put a bit of fraycheck on.

Ta-dah!

11.b Green-Version (probably better for trousers where you’re not topstitching the waistband!)

(This is where I carefully trim off the top of the zip. I also trim the seam allowances where the button hole will be as this bit can sometimes prove tricky for my machine to get through)


Then, just before the button & buttonhole, I topstitch all the way around. This is tough going over all the fabric at the belt loops, and totally negates the point of having them tucked into the seam! Next time I’ll use the green version but stitch the tops of the loops at the end like a normal person! How do you do it?


While I’ve got my double thread in, I stitch the seam down the side, from the waistband to the bottom of the pocket bag. This is both decorative and strengthens the seam.

Almost there…!

12. Button & Buttonhole. 

I tinkered around loads and really got to know my buttonhole settings! It was a very enjoyable half hour and, if you haven’t yet, I highly recommend you do it!

The problem came when I put the waistband into the machine. All my practice went to waste as my machine didn’t like it. I ended up having to freestyle a buttonhole using the zigzag stitch. Somehow, when I mustn’t have been looking, one of my belt loops ended up a bit close to the front and was getting in my way. I know if I start unpicking the waistband now it’ll end up like a dogs dinner, so I’m going with it. I don’t think I’ll be arrested…!

I cut the buttonhole with a sharp unpicker. I use a pin at the end to stop me from overshooting. Then, as I haven’t got the right rivets or button yet, I attached this nice button, reclaimed from a firemans uniform from oxfam.


13. Hem. 

This is it! The final stage!

I’d already washed the fabric but I read somewhere that denim can keep shrinking for a while, so as a small concession to that, I washed them again before hemming.

I put them on, put my trainers on and folded until I was happy with the length. Stupidly, I’m always nervous about hemming trousers. If they’re too short, that’s it! All over! I’m the same with putting the buttons on a shirt, I suppose it’s because it’s the last chance to muck it up! … There’s confidence for you! Ha!

Anyway, these ones turned out ok! And here they are, all ready to wear to MadRachael’s birthday party in Brighton at the weekend…


Blimey, if you’ve made it this far, thank you for sticking with me! If you’ve made jeans before and can share any tips with me I’d love to hear them. If you’ve not made jeans, I hope you feel inspired to try some. Like all big jobs, making jeans is just lots of small jobs, put together. You can move a mountain… Only just one rock at a time!

Thanks for reading!

Happy sewing!

Notes to self:

Exit mobile version